Nissan Murano Z50/Ключ-брелок
Материал из NissanWiki
(Различия между версиями)
K001 (Обсуждение | вклад) (moar) |
K001 (Обсуждение | вклад) (Notes from BL-70 added) |
||
| Строка 1: | Строка 1: | ||
| + | Процедура прописывания нового ключа-брелка описана в сервис-мануале, стр. BL-79 и BL-80. | ||
| + | |||
| + | * If a key fob is lost, the ID code of the lost key fob must be erased to prevent unauthorized use. A specific ID code can be erased with CONSULT-II. However, when the ID code of a lost key fob is not known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new key fobs must be re-registered. | ||
| + | * To erase all ID codes in memory, register one ID code (key fob) five times. After all ID codes are erased, the ID codes of all remaining and/or new key fobs must be re-registered. | ||
| + | |||
| + | * When registering an additional key fob, the existing ID codes in memory may or may not be erased. If five ID codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added and no ID codes are erased. | ||
| + | |||
| + | * If you need to activate more than two additional new key fobs, repeat the procedure "Additional ID code entry" for each new key fob. | ||
| + | |||
| + | * Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code will be erased. | ||
| + | |||
| + | * Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is counted as an additional code. | ||
| + | |||
| + | |||
| + | |||
| + | |||
<pre> | <pre> | ||
To reprogram your key fob (keyless entry remote) | To reprogram your key fob (keyless entry remote) | ||
Версия 06:17, 15 января 2013
Процедура прописывания нового ключа-брелка описана в сервис-мануале, стр. BL-79 и BL-80.
- If a key fob is lost, the ID code of the lost key fob must be erased to prevent unauthorized use. A specific ID code can be erased with CONSULT-II. However, when the ID code of a lost key fob is not known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new key fobs must be re-registered.
- To erase all ID codes in memory, register one ID code (key fob) five times. After all ID codes are erased, the ID codes of all remaining and/or new key fobs must be re-registered.
- When registering an additional key fob, the existing ID codes in memory may or may not be erased. If five ID codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added and no ID codes are erased.
- If you need to activate more than two additional new key fobs, repeat the procedure "Additional ID code entry" for each new key fob.
- Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code will be erased.
- Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is counted as an additional code.
To reprogram your key fob (keyless entry remote) 1.Get in & lock the doors 2.Insert the key into the ignition 20 times within 15 seconds (or until the Hazard lights flash) 3.Hazard lights should flash 4.Put key back into the ignition & turn to Accessory 5.Press the master door lock (on drivers door arm rest) unlock/lock 6.Hit the lock button on the remote 7.Hazards should flash 8.Pull key out and open the drivers door and then close it 9.It should be set -- Hop in and lock the doors with the door switch Insert the key in and out once per second until you see the hazards flash. Then after hazards have flashed, insert key and turn to on position. Once everythings lit up, press any button on your remote The hazard lights should blink indicating it took the programming Then if you have any additional remotes you wish to program While ignition is still on, press the unlock then lock buttons on the door switch Then press any button on the second remote If you have more remotes, repeat above steps. Once your done, shut off key and pull it out Manually open door and done.
